-------------CRC16_SX.ASM---------------------- ;By Charles Ader ;Translated to SX by Nikolai Golovchenko RESET start crc_hi DS 1 crc_lo DS 1 ;******************************************************************** ; CRC Test Program ;******************************************************************** org 1h start clr crc_hi clr crc_lo mov W, #080H ; crc_hi:crc_lo = 00 00 call CRC16 mov W, #075H ; crc_hi:crc_lo = A0 01 call CRC16 mov W, #08AH ; crc_hi:crc_lo = 27 A0 call CRC16 mov W, #00BH ; crc_hi:crc_lo = DF A6 call CRC16 mov W, #075H ; crc_hi:crc_lo = BD 1E call CRC16 mov W, #0C7H ; crc_hi:crc_lo = EF FC call CRC16 mov W, #0AAH ; crc_hi:crc_lo = D3 AE call CRC16 mov W, #075H ; crc_hi:crc_lo = C3 D2 call CRC16 mov W, #0C7H ; crc_hi:crc_lo = BA 82 call CRC16 mov W, #055H ; crc_hi:crc_lo = F3 7B call CRC16 mov W, #043H ; crc_hi:crc_lo = 1C 73 call CRC16 mov W, #01CH ; crc_hi:crc_lo = 14 1c call CRC16 mov W, #014H ; crc_hi:crc_lo = 00 14 call CRC16 jmp start ; crc_hi:crc_lo = 00 00 ;******************************************************************** ; ; CRC-16 (x^16+x^15+x^2+x^0) ; No tables, No loops, No temporary registers used. ; ; Input: W = Data byte for CRC calculation ; crc_hi:crc_lo 16 bit CRC register ; ; Output: crc_hi:crc_lo updated. ; ; Notes: CARRY is trashed. ; DIGIT CARRY is trashed. ; ZERO is trashed. ; W is zero on exit. ; ; 30 instructions, 32 machine cycles per byte. ; ; Copyright (C) February 8, 2000. All Right Reserved. ; Charles Ader, PO Box 940 Pleasanton, California, USA. ; ; This code started out as an example program found in ; Dallas Semiconductor Application Note 27: ; ; Understanding and Using Cyclic Redundancy Checks ; with Dallas Semiconductor iButton(TM) Products. ; ; The application note shows an 8051 assembly language ; routine that calculates the same CRC as the hardware ; in the DS5001/2 secure micro. ; ;******************************************************************** CRC16 xor W, crc_lo ;W = input XOR old crc_lo xor W, crc_hi ;Swap old crc_hi with W xor crc_hi, W ; xor W, crc_hi ;new crc_hi = input XOR old crc_lo mov crc_lo, W ;new crc_lo = old crc_hi ; ; Calculate parity of crc_hi, (input XOR old crc_lo), ; an place the result in carry. ; ; Save crc_hi in W and use crc_hi as a temp ; location so we can test bits. ; ; Note: We use INC STATUS to compliment ; carry. This is safe because the XOR ; will clear the zero flag if any of the ; inc instructions are going to execute. ; ; The inc can be executed a maximum of ; four times after the XOR before the ; bits to the left of zero in status will ; be affected. ; ; We use INC at most three time here. ; ; Note by NG: INC instruction doesn't work this way ; on SX chip. But INCSZ does! Since Z flag is ; set to zero if any INCSZ are going to execute, ; then STATUS will never reach zero after three ; INCSZ. Therefore skip is never executed. mov W, crc_hi ;Save crc_hi in W swap crc_hi ;Trade nibbles xor crc_hi, W ;XOR high half byte with low rr crc_hi ;Initialize Carry snb crc_hi.0 incsz STATUS ;Compliment carry snb crc_hi.1 incsz STATUS ;Compliment carry snb crc_hi.2 incsz STATUS ;Compliment carry mov crc_hi, W ;Restore crc_hi from W ; ; Use the parity of crc_hi, (input XOR crc_lo), ; to complete the CRC calculation. ; mov W, #001H snb C ; If carry xor crc_lo, W ; flip bit 0 of crc_lo mov W, #040H rr crc_hi ; shift parity into crc_hi snb C ; if shift out is one xor crc_lo, W ; flip bit 6 of crc_lo mov W, <<crc&hi ; unshift crc_hi into W xor crc_hi, W ; combine them rr crc_hi ; shift parity back into crc_hi mov W, #080H snb C ; if shift out is one xor crc_lo, W ; flip bit 7 of crc_lo retw 0 -------------End CRC16_SX.ASM------------------
-------------CRC16.ASM----------------------
;By Charles Ader
;********************************************************************
;
; Compiled with MAPLAB 4.12.12
;
;********************************************************************
LIST p=16C54 ; PIC16C54 is the target processor
crc_hi equ 00EH
crc_lo equ 00FH
STATUS equ 3 ; STATUS register F3
CARRY equ 0 ; Carry bit in status register
;********************************************************************
; CRC Test Program
;********************************************************************
org 0h
start clrf crc_hi
clrf crc_lo
movlw 080H ; crc_hi:crc_lo = 00 00
call CRC16
movlw 075H ; crc_hi:crc_lo = A0 01
call CRC16
movlw 08AH ; crc_hi:crc_lo = 27 A0
call CRC16
movlw 00BH ; crc_hi:crc_lo = DF A6
call CRC16
movlw 075H ; crc_hi:crc_lo = BD 1E
call CRC16
movlw 0C7H ; crc_hi:crc_lo = EF FC
call CRC16
movlw 0AAH ; crc_hi:crc_lo = D3 AE
call CRC16
movlw 075H ; crc_hi:crc_lo = C3 D2
call CRC16
movlw 0C7H ; crc_hi:crc_lo = BA 82
call CRC16
movlw 055H ; crc_hi:crc_lo = F3 7B
call CRC16
movlw 043H ; crc_hi:crc_lo = 1C 73
call CRC16
movlw 01CH ; crc_hi:crc_lo = 14 1c
call CRC16
movlw 014H ; crc_hi:crc_lo = 00 14
call CRC16
goto start ; crc_hi:crc_lo = 00 00
;********************************************************************
;
; CRC-16 (x^16+x^15+x^2+x^0)
; No tables, No loops, No temporary registers used.
;
; Input: W = Data byte for CRC calculation
; crc_hi:crc_lo 16 bit CRC register
;
; Output: crc_hi:crc_lo updated.
;
; Notes: CARRY is trashed.
; DIGIT CARRY is trashed.
; ZERO is trashed.
; W is zero on exit.
;
; 30 instructions, 31 machine cycles per byte.
;
; Copyright (C) February 8, 2000. All Right Reserved.
; Charles Ader, PO Box 940 Pleasanton, California, USA.
;
; This code started out as an example program found in
; Dallas Semiconductor Application Note 27:
;
; Understanding and Using Cyclic Redundancy Checks
; with Dallas Semiconductor iButton(TM) Products.
;
; The application note shows an 8051 assembly language
; routine that calculates the same CRC as the hardware
; in the DS5001/2 secure micro.
;
;********************************************************************
CRC16 xorwf crc_lo,W ;W = input XOR old crc_lo
xorwf crc_hi,W ;Swap old crc_hi with W
xorwf crc_hi,F ;
xorwf crc_hi,W ;new crc_hi = input XOR old crc_lo
movwf crc_lo ;new crc_lo = old crc_hi
;
; Calculate parity of crc_hi, (input XOR old crc_lo),
; an place the result in carry.
;
; Save crc_hi in W and use crc_hi as a temp
; location so we can test bits.
;
; Note: We use INCF STATUS,F to compliment
; carry. This is safe because the XORWF
; will clear the zero flag if any of the
; INCF instructions are going to execute.
;
; The INCF can be executed a maximum of
; four times after the XORWF before the
; bits to the left of zero in status will
; be affected.
;
; We use INCF at most three time here.
;
movf crc_hi,W ;Save crc_hi in W
swapf crc_hi,F ;Trade nibbles
xorwf crc_hi,F ;XOR high half byte with low
rrf crc_hi,F ;Initialize Carry
btfsc crc_hi,0
incf STATUS,F ;Compliment carry
btfsc crc_hi,1
incf STATUS,F ;Compliment carry
btfsc crc_hi,2
incf STATUS,F ;Compliment carry
movwf crc_hi ;Restore crc_hi from W
;
; Use the parity of crc_hi, (input XOR crc_lo),
; to complete the CRC calculation.
;
movlw 001H
btfsc STATUS,CARRY ; If carry
xorwf crc_lo,F ; flip bit 0 of crc_lo
movlw 040H
rrf crc_hi,F ; shift parity into crc_hi
btfsc STATUS,CARRY ; if shift out is one
xorwf crc_lo,F ; flip bit 6 of crc_lo
rlf crc_hi,W ; unshift crc_hi into W
xorwf crc_hi,F ; combine them
rrf crc_hi,F ; shift parity back into crc_hi
movlw 080H
btfsc STATUS,CARRY ; if shift out is one
xorwf crc_lo,F ; flip bit 7 of crc_lo
retlw 0
;********************************************************************
; Power on reset
;********************************************************************
org 01FFH
goto start
end
-------------End CRC16.ASM------------------
Here is the same CRC16 routine for the x86 and 8051
----------CRC16.C for x86 start------------------------
#include <stdio.h>
/********************************************************************
CRC-16 (x^16+x^15+x^2+x^0)
No tables, No jumps.
Input: c = Data byte for CRC calculation
usp_crc = pointer to 16 bit CRC register
Output: CRC at pointer usp_crc is updated
Copyright (C) February 11, 2000. All Right Reserved.
Charles Ader, PO Box 940 Pleasanton, California, USA.
This code started out as an example program found in
Dallas Semiconductor Application Note 27:
Understanding and Using Cyclic Redundancy Checks
with Dallas Semiconductor iButton(TM) Products.
The application note shows an 8051 assembly language
routine that calculates the same CRC as the hardware
in the DS5001/2 secure micro.
********************************************************************/
void crc16(unsigned short *usp_crc, unsigned char c)
{
unsigned short crc; /* use a local temp so the compiler will */
/* handle all the x86 pointer crap. */
crc = *usp_crc;
_asm {
mov al,c
mov cx,crc
XOR AL,CL
MOV CL,CH
MOV CH,AL
LAHF
NOT AH
RCR AH,1
RCR AH,1
AND AH,1
XOR CL,AH
RCR AX,1
SBB AH,AH
AND AH,0x40
XOR CL,AH
MOV AH,AL
XOR AL,CH
RCL AH,1
RCR AL,1
MOV CH,AL
RCR AL,1
AND AL,0x80
XOR CL,AL
mov crc,cx
}
*usp_crc = crc;
}
/******************************************************
* MAIN FUNCTION *
*******************************************************/
main()
{
unsigned int crc;
while(1) {
crc = 0; /* crc = 0x0000 */
crc16(&crc,0x80); /* crc = 0xA001 */
crc16(&crc,0x75); /* crc = 0x27A0 */
crc16(&crc,0x8A); /* crc = 0xDFA6 */
crc16(&crc,0x0B); /* crc = 0xBD1E */
crc16(&crc,0x75); /* crc = 0xEFFC */
crc16(&crc,0xC7); /* crc = 0xD3AE */
crc16(&crc,0xAA); /* crc = 0xC3D2 */
crc16(&crc,0x75); /* crc = 0xBA82 */
crc16(&crc,0xC7); /* crc = 0xF37B */
crc16(&crc,0x55); /* crc = 0x1C73 */
crc16(&crc,0x43); /* crc = 0x141C */
crc16(&crc,0x1C); /* crc = 0x0014 */
crc16(&crc,0x14); /* crc = 0x0000 */
}
} /* end of main */
----------CRC16.C for x86 end ------------------------
----------CRC16.A51 for 8051 start---------------------
;
; From Dallas Application note 27
;
; CRC-16 (x^16+x^15+x^2+x^0)
; No tables, No loops, No temporary registers used.
;
; This code is from Dallas Semiconductor Application Note 27:
;
; Understanding and Using Cyclic Redundancy Checks
; with Dallas Semiconductor iButton(TM) Products.
;
; This routine that calculates the same CRC as the hardware
; in the DS5001/2 secure micro.
;-----------------------------------------------------------------------
NAME CRC_test
?DT?CRC_test SEGMENT DATA
rseg ?DT?CRC_test
CRCH: ds 1
CRCL: ds 1
?CO?CRC_test SEGMENT CODE
RSEG ?CO?CRC_test
public CRC_test
CRC_test:
mov CRCH,#0
mov CRCL,#0
mov A,#080H
call CRC16
mov A,#075H
call CRC16
mov A,#08AH
call CRC16
mov A,#00BH
call CRC16
mov A,#075H
call CRC16
mov A,#0C7H
call CRC16
mov A,#0AAH
call CRC16
mov A,#075H
call CRC16
mov A,#0C7H
call CRC16
mov A,#055H
call CRC16
mov A,#043H
call CRC16
ljmp CRC_test
;CALCULATE CRC16 IN PARALLEL TO THE GREATEST EXTENT PRACTICAL
; INPUT: BYTE TO BE INCUDED IN CRC CALCULATION IS IN ACC
; OUTPUT: CRCH:CRCL UPDATED TO INCLUDE THE NEW BYTE
;
CRC16:
PUSH ACC ;save this in case the caller needs
it
XRL A,CRCL
MOV CRCL,CRCH ;put the high byte of the crc in its
dest..
MOV CRCH,A ;save data xor low(crc) for later
MOV C,P
JNC CRC0
XRL CRCL,#001H
CRC0:
RRC A ;get the low bit in c
JNC CRC1
XRL CRCL,#040H
CRC1:
MOV C,ACC.7
XRL A,CRCH ;compute the results for bits P...U
RRC A ;shift them into place
MOV CRCH,A ;and save them
JNC CRC2
XRL CRCL,#080H
CRC2:
POP ACC ;and restore everything and return
RET
end
----------CRC16.A51 for 8051 end ---------------------
Questions:
Hello,+
I've tried the code shown above for the PIC micro (on a 16F877A and 16F84A targets). The simulation with the MPLAB software works fine but when I try to run this code on any of the target processors the results are quite different (don't work).
For example, at the initial stage I load crc_hi and crc_lo registers with 0xFF the buffer pattern is: 02-01-01-00-10-03 (all in HEX) and when I update the CRC calculation with all the bytes contained at the buffer including the last one, I xor the final result with 0xFF, so the result must be crc_hi=8F, crc_lo= FB. This works fine in MPLAB but, when I run this code in the PICmicro I found that the results given are crc_hi=8E, crc_lo=3B. The results are wrong!
Pseudo code for the above:
crc_hi = crc_lo = 0xFF;
update crc for all buffer bytes;
crc_hi = crc_hi XOR 0xFF;
crc_lo = crc_lo XOR 0xFF;
Even more, using the same target processors and a different buffer for the CRC calculation (01-04-01-01-10-03) the resulting CRC is: crc_hi=12, crc_lo=08. This works fine on the MPLAB IDE and when I run this code on the PIC micro runs OK too!! With this pattern the code works!
So, the question is, why the code runs fine on the MPLAB IDE for all tests made and for all patterns and why not on the PICmicro? any initial missconfiguration or something like that?
I hope anybody can help me solving this trouble!!
Regards,
Elkin.
| file: /Techref/scenix/lib/io/osi2/crc16ca_sx.htm, 20KB, , updated: 2013/7/22 17:15, local time: 2024/12/27 20:43,
18.191.63.237:LOG IN
|
| ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions? <A HREF="http://ecomorder.com/Techref/scenix/lib/io/osi2/crc16ca_sx.htm"> SX Specific Cyclic Redundancy Check </A> |
| Did you find what you needed? |
Welcome to ecomorder.com! |
Welcome to ecomorder.com! |
.