Code:
;*****************************************************************************************
; Copyright © [01/26/1999] Scenix Semiconductor, Inc. All rights reserved.
;
; Scenix Semiconductor, Inc. assumes no responsibility or liability for
; the use of this [product, application, software, any of these products].
; Scenix Semiconductor conveys no license, implicitly or otherwise, under
; any intellectual property rights.
; Information contained in this publication regarding (e.g.: application,
; implementation) and the like is intended through suggestion only and may
; be superseded by updates. Scenix Semiconductor makes no representation
; or warranties with respect to the accuracy or use of these information,
; or infringement of patents arising from such use or otherwise.
;*****************************************************************************************
;
; Filename: SX52_timers.src
;
; Authors: Stephen Holland
; Sr. Applications Engineer
; Scenix Semiconductor
;
; Revision: 1.00
;
; Part: SX52BD datecode AA9931AC
; Freq: 50Mhz
; Compiler: Parallax SX-Key52 software v1.12 and SASM 1.40
;
; Date Written: 10/16/99
;
; Last Revised: 10/31/99
;
; Program Description:
;
; This code demonstrates the various modes of the SX48BD and SX52BD onboard 16-bit
; timers.
;
; Revision History:
; 10/31/99 - Added timer capture functions set_CP1 and set_CP2 (each function monitors
; both capture sources on the timer).
;
;*****************************************************************************************
;*****************************************************************************************
; Target SX
; Uncomment one of the following lines to choose the SX48BD/ES, SX48BD, SX52BD/ES or SX52BD.
; For SX48BD/ES and SX52BD/ES, uncomment both defines, SX48_52 and SX48_52_ES.
;*****************************************************************************************
;SX48_52
SX48_52_ES
;*****************************************************************************************
; Assembler Used
; Uncomment the following line if using the Parallax SX-Key assembler. SASM assembler
; enabled by default.
;*****************************************************************************************
SX_Key
;*********************************************************************************
; Assembler directives:
; high speed external osc, turbo mode, 8-level stack, and extended option reg.
;
; SX18/20/28 - 4 pages of program memory and 8 banks of RAM enabled by default.
; SX48/52 - 8 pages of program memory and 16 banks of RAM enabled by default.
;
;*********************************************************************************
IFDEF SX_Key ;SX-Key Directives
IFDEF SX48_52_ES ;SX48BD/ES or SX52BD/ES device directives for SX-Key
device oschs,turbo,stackx,optionx
ELSE
IFDEF SX48_52 ;SX48/52/BD device directives for SX-Key
device oschs2
ENDIF
ENDIF
freq 50_000_000
ELSE ;SASM Directives
IFDEF SX48_52_ES ;SX48BD/ES or SX52BD/ES device directives for SASM
device SX52,oschs,turbo,stackx,optionx
ELSE
IFDEF SX48_52 ;SX48BD or SX52BD device directives for SASM
device SX52,oschs2
ENDIF
ENDIF
ENDIF
id ' ' ;
reset reset_entry ; set reset vector
;*****************************************************************************************
; Macros
;*****************************************************************************************
;*********************************************************************************
; Macro: _bank
; Sets the bank appropriately for all revisions of SX.
;
; This is required since the bank instruction has only a 3-bit operand, it cannot
; be used to access all 16 banks of the SX48/52. For this reason FSR.4 (for SX48/52BD/ES)
; or FSR.7 (SX48/52bd production release) needs to be set appropriately, depending
; on the bank address being accessed. This macro fixes this.
;
; So, instead of using the bank instruction to switch between banks, use _bank instead.
;
;*********************************************************************************
_bank macro 1
expand
bank \1
noexpand
IFDEF SX48_52
IFDEF SX48_52_ES
IF \1 & %00010000 ;SX48BD/ES and SX52BD/ES (engineering sample) bank instruction
expand
setb fsr.4 ;modifies FSR bits 5,6 and 7. FSR.4 needs to be set by software.
noexpand
ENDIF
ELSE
IF \1 & %10000000 ;SX48BD and SX52BD (production release) bank instruction
expand
setb fsr.7 ;modifies FSR bits 4,5 and 6. FSR.7 needs to be set by software.
noexpand
ELSE
expand
clrb fsr.7
noexpand
ENDIF
ENDIF
ENDIF
endm
;*********************************************************************************
; Macro: _mode
; Sets the MODE register appropriately for all revisions of SX.
;
; This is required since the MODE (or MOV M,#) instruction has only a 4-bit operand.
; The SX18/20/28AC use only 4 bits of the MODE register, however the SX48/52BD have
; the added ability of reading or writing some of the MODE registers, and therefore use
; 5-bits of the MODE register. The MOV M,W instruction modifies all 8-bits of the
; MODE register, so this instruction must be used on the SX48/52BD to make sure the MODE
; register is written with the correct value. This macro fixes this.
;
; So, instead of using the MODE or MOV M,# instructions to load the M register, use
; _mode instead.
;
;*********************************************************************************
_mode macro 1
noexpand
IFDEF SX48_52
expand
mov w,#\1 ;loads the M register correctly for the SX48BD and SX52BD
mov m,w
noexpand
ELSE
expand
mov m,#\1 ;loads the M register correctly for the SX18AC, SX20AC
;and SX28AC
noexpand
ENDIF
endm
IFDEF SX_Key
;*****************************************************************************************
; Debugger Watches (SX-Key software only)
;*****************************************************************************************
watch T1cap1_done,1,ubin
watch T1CAP1L,16,uhex
watch T1cap2_done,1,ubin
watch T1CAP2L,16,uhex
watch T2cap1_done,1,ubin
watch T2CAP1L,16,uhex
watch T2cap2_done,1,ubin
watch T2CAP2L,16,uhex
ENDIF
;*****************************************************************************************
; Data Memory address definitions
; These definitions ensure the proper address is used for banks 0 - 7 for 2K SX devices
; (SX18/20/28) and 4K SX devices (SX48/52).
;*****************************************************************************************
global_org = $0A
bank0_org = $00
bank1_org = $10
bank2_org = $20
bank3_org = $30
bank4_org = $40
bank5_org = $50
bank6_org = $60
bank7_org = $70
;*****************************************************************************************
; Global Register definitions
; NOTE: Global data memory starts at $0A on SX48/52 and $08 on SX18/20/28.
;*****************************************************************************************
org global_org
function_temp equ global_org
global_temp equ global_org+1
flags equ global_org+2 ;program flags register
timer_flag equ flags.0 ;indicates a timeout on the software 16-bit timer
T1cap1_done equ flags.1 ;indicates T1 capture 1 done
T1cap2_done equ flags.2 ;indicates T1 capture 2 done
T2cap1_done equ flags.3 ;indicates T2 capture 1 done
T2cap2_done equ flags.4 ;indicates T2 capture 2 done
;*****************************************************************************************
; RAM Bank Register definitions
;*****************************************************************************************
;*********************************************************************************
; Bank 0
;*********************************************************************************
org bank0_org
bank0 = $
;*********************************************************************************
; Bank 1
;*********************************************************************************
org bank1_org
bank1 = $
timers = $
t1_hdc_high ds 1 ;T1R1CMH value
t1_hdc_low ds 1 ;T1R1CML value
t1_ldc_high ds 1 ;T1R2CMH value
t1_ldc_low ds 1 ;T1R2CML value
t2_hdc_high ds 1 ;T2R1CMH value
t2_hdc_low ds 1 ;T2R1CML value
t2_ldc_high ds 1 ;T2R2CMH value
t2_ldc_low ds 1 ;T2R2CML value
T1CAP1L ds 1 ;T1 capture 1 low byte
T1CAP1H ds 1 ;T1 capture 1 high byte
T1CAP2L ds 1 ;T1 capture 2 low byte
T1CAP2H ds 1 ;T1 capture 2 high byte
T2CAP1L ds 1 ;T2 capture 1 low byte
T2CAP1H ds 1 ;T2 capture 1 high byte
T2CAP2L ds 1 ;T2 capture 2 low byte
T2CAP2H ds 1 ;T2 capture 2 high byte
;*********************************************************************************
; Bank 2
;*********************************************************************************
org bank2_org
bank2 = $
timer_vp = $
timer_low ds 1 ;timer accumulator low byte
timer_high ds 1 ;timer accumulator high byte
;*********************************************************************************
; Bank 3
;*********************************************************************************
org bank3_org
bank3 = $
;*********************************************************************************
; Bank 4
;*********************************************************************************
org bank4_org
bank4 = $
;*********************************************************************************
; Bank 5
;*********************************************************************************
org bank5_org
bank5 = $
;*********************************************************************************
; Bank 6
;*********************************************************************************
org bank6_org
bank6 = $
;*********************************************************************************
; Bank 7
;*********************************************************************************
org bank7_org
bank7 = $
;*********************************************************************************
; Bank 8
;*********************************************************************************
org $80 ;bank 8 address on SX52
bank8 = $
;*********************************************************************************
; Bank 9
;*********************************************************************************
org $90 ;bank 9 address on SX52
bank9 = $
;*********************************************************************************
; Bank A
;*********************************************************************************
org $A0 ;bank A address on SX52
bankA = $
;*********************************************************************************
; Bank B
;*********************************************************************************
org $B0 ;bank B address on SX52
bankB = $
;*********************************************************************************
; Bank C
;*********************************************************************************
org $C0 ;bank C address on SX52
bankC = $
;*********************************************************************************
; Bank D
;*********************************************************************************
org $D0 ;bank D address on SX52
bankD = $
;*********************************************************************************
; Bank E
;*********************************************************************************
org $E0 ;bank E address on SX52
bankE = $
;*********************************************************************************
; Bank F
;*********************************************************************************
org $F0 ;bank F address on SX52
bankF = $
;*****************************************************************************************
; Port Assignment
;*****************************************************************************************
RA_latch equ %00000000 ;SX18/20/28/48/52 port A latch init
RA_DDIR equ %11111111 ;SX18/20/28/48/52 port A DDIR value
RA_LVL equ %00000000 ;SX18/20/28/48/52 port A LVL value
RA_PLP equ %11111111 ;SX18/20/28/48/52 port A PLP value
RB_latch equ %00000000 ;SX18/20/28/48/52 port B latch init
RB_DDIR equ %10111111 ;SX18/20/28/48/52 port B DDIR value
RB_ST equ %11111111 ;SX18/20/28/48/52 port B ST value
RB_LVL equ %00000000 ;SX18/20/28/48/52 port B LVL value
RB_PLP equ %11111111 ;SX18/20/28/48/52 port B PLP value
RC_latch equ %00000000 ;SX18/20/28/48/52 port C latch init
RC_DDIR equ %11111011 ;SX18/20/28/48/52 port C DDIR value
RC_ST equ %11111111 ;SX18/20/28/48/52 port C ST value
RC_LVL equ %00000000 ;SX18/20/28/48/52 port C LVL value
RC_PLP equ %11111111 ;SX18/20/28/48/52 port C PLP value
RD_latch equ %00000000 ;SX48/52 port D latch init
RD_DDIR equ %11111111 ;SX48/52 port D DDIR value
RD_ST equ %11111111 ;SX48/52 port D ST value
RD_LVL equ %00000000 ;SX48/52 port D LVL value
RD_PLP equ %11111111 ;SX48/52 port D PLP value
RE_latch equ %00000000 ;SX48/52 port E latch init
RE_DDIR equ %01111111 ;SX48/52 port E DDIR value
RE_ST equ %11111111 ;SX48/52 port E ST value
RE_LVL equ %00000000 ;SX48/52 port E LVL value
RE_PLP equ %11111111 ;SX48/52 port E PLP value
;*****************************************************************************************
; Pin Definitions
;*****************************************************************************************
timer_pin equ re.7 ;flashing timer LED
;*****************************************************************************************
; Program constants
;*****************************************************************************************
int_period = 217 ;RTCC Interrupt rate
; = 1/(int_period*RTCC prescaler*1/50MHz)
; = 1/(217*1*20ns) = 4.34us
;*********************************************************************************
; SX48BD/52BD Mode addresses
; *On SX48BD/52BD, most registers addressed via mode are read and write, with the
; exception of CMP and WKPND which do an exchange with W.
;*********************************************************************************
; Timer (read) addresses
TCPL_R equ $00 ;Read Timer Capture register low byte
TCPH_R equ $01 ;Read Timer Capture register high byte
TR2CML_R equ $02 ;Read Timer R2 low byte
TR2CMH_R equ $03 ;Read Timer R2 high byte
TR1CML_R equ $04 ;Read Timer R1 low byte
TR1CMH_R equ $05 ;Read Timer R1 high byte
TCNTB_R equ $06 ;Read Timer control register B
TCNTA_R equ $07 ;Read Timer control register A
; Exchange addresses
CMP equ $08 ;Exchange Comparator enable/status register with W
WKPND equ $09 ;Exchange MIWU/RB Interrupts pending with W
; Port setup (read) addresses
WKED_R equ $0A ;Read MIWU/RB Interrupt edge setup, 0 = falling, 1 = rising
WKEN_R equ $0B ;Read MIWU/RB Interrupt edge setup, 0 = enabled, 1 = disabled
ST_R equ $0C ;Read Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
LVL_R equ $0D ;Read Port Level setup, 0 = CMOS, 1 = TTL
PLP_R equ $0E ;Read Port Weak Pullup setup, 0 = enabled, 1 = disabled
DDIR_R equ $0F ;Read Port Direction
; Timer (write) addresses
CLR_TMR equ $10 ;Resets 16-bit Timer
TR2CML_W equ $12 ;Write Timer R2 low byte
TR2CMH_W equ $13 ;Write Timer R2 high byte
TR1CML_W equ $14 ;Write Timer R1 low byte
TR1CMH_W equ $15 ;Write Timer R1 high byte
TCNTB_W equ $16 ;Write Timer control register B
TCNTA_W equ $17 ;Write Timer control register A
; Port setup (write) addresses
WKED_W equ $1A ;Write MIWU/RB Interrupt edge setup, 0 = falling, 1 = rising
WKEN_W equ $1B ;Write MIWU/RB Interrupt edge setup, 0 = enabled, 1 = disabled
ST_W equ $1C ;Write Port Schmitt Trigger setup, 0 = enabled, 1 = disabled
LVL_W equ $1D ;Write Port Level setup, 0 = CMOS, 1 = TTL
PLP_W equ $1E ;Write Port Weak Pullup setup, 0 = enabled, 1 = disabled
DDIR_W equ $1F ;Write Port Direction
;*****************************************************************************************
; Interrupt Service Routine
;*****************************************************************************************
; Note: The interrupt code must always originate at address $0.
;
; Interrupt Frequency = (Cycle Frequency / -(retiw value)) For example:
; With a retiw value of -217 and an oscillator frequency of 50MHz, this
; code runs every 4.34us.
;*****************************************************************************************
org $0
interrupt ;3
;*********************************************************************************
; Virtual Peripheral: 16-bit Timer
;
;
; Input variable(s):
; Output variable(s):
; Variable(s) affected:
; Flag(s) affected:
;*********************************************************************************
:16bit_timer _bank timer_vp
inc timer_low ;adjust timer's accumulator
snb z
inc timer_high ; (timer = 16 bits long)
snz
setb timer_flag
;toggle_led
sb timer_high.6 ;toggle timer (square wave)
clrb timer_pin
snb timer_high.6
setb timer_pin
;*********************************************************************************
; Set Interrupt Rate
;*********************************************************************************
isr_end mov w,#-int_period ;refresh RTCC on return
retiw ;return from the interrupt
; = 1/(int_period*RTCC prescaler*1/50MHz)
; = 1/(217*1*20ns) = 4.34us
;*****************************************************************************************
; End of the Interrupt Service Routine
;*****************************************************************************************
;*****************************************************************************************
; RESET VECTOR
;*****************************************************************************************
;*********************************************************************************
; Program execution begins here on power-up or after a reset
;*********************************************************************************
reset_entry
;*********************************************************************************
; Initialise all port configuration
;*********************************************************************************
_mode ST_W ;point MODE to write ST register
mov w,#RB_ST ;Setup RB Schmitt Trigger, 0 = enabled, 1 = disabled
mov !rb,w
mov w,#RC_ST ;Setup RC Schmitt Trigger, 0 = enabled, 1 = disabled
mov !rc,w
mov w,#RD_ST ;Setup RD Schmitt Trigger, 0 = enabled, 1 = disabled
mov !rd,w
mov w,#RE_ST ;Setup RE Schmitt Trigger, 0 = enabled, 1 = disabled
mov !re,w
_mode LVL_W ;point MODE to write LVL register
mov w,#RA_LVL ;Setup RA CMOS or TTL levels, 0 = TTL, 1 = CMOS
mov !ra,w
mov w,#RB_LVL ;Setup RB CMOS or TTL levels, 0 = TTL, 1 = CMOS
mov !rb,w
mov w,#RC_LVL ;Setup RC CMOS or TTL levels, 0 = TTL, 1 = CMOS
mov !rc,w
mov w,#RD_LVL ;Setup RD CMOS or TTL levels, 0 = TTL, 1 = CMOS
mov !rd,w
mov w,#RE_LVL ;Setup RE CMOS or TTL levels, 0 = TTL, 1 = CMOS
mov !re,w
_mode PLP_W ;point MODE to write PLP register
mov w,#RA_PLP ;Setup RA Weak Pull-up, 0 = enabled, 1 = disabled
mov !ra,w
mov w,#RB_PLP ;Setup RB Weak Pull-up, 0 = enabled, 1 = disabled
mov !rb,w
mov w,#RC_PLP ;Setup RC Weak Pull-up, 0 = enabled, 1 = disabled
mov !rc,w
mov w,#RD_PLP ;Setup RD Weak Pull-up, 0 = enabled, 1 = disabled
mov !rd,w
mov w,#RE_PLP ;Setup RE Weak Pull-up, 0 = enabled, 1 = disabled
mov !re,w
_mode DDIR_W ;point MODE to write DDIR register
mov w,#RA_DDIR ;Setup RA Direction register, 0 = output, 1 = input
mov !ra,w
mov w,#RB_DDIR ;Setup RB Direction register, 0 = output, 1 = input
mov !rb,w
mov w,#RC_DDIR ;Setup RC Direction register, 0 = output, 1 = input
mov !rc,w
mov w,#RD_DDIR ;Setup RD Direction register, 0 = output, 1 = input
mov !rd,w
mov w,#RE_DDIR ;Setup RE Direction register, 0 = output, 1 = input
mov !re,w
mov w,#RA_latch ;Initialize RA data latch
mov ra,w
mov w,#RB_latch ;Initialize RB data latch
mov rb,w
mov w,#RC_latch ;Initialize RC data latch
mov rc,w
mov w,#RD_latch ;Initialize RD data latch
mov rd,w
mov w,#RE_latch ;Initialize RE data latch
mov re,w
;*********************************************************************************
; Clear all Data RAM locations
;*********************************************************************************
;SX48/52 RAM clear routine
mov w,#$0a ;reset all ram starting at $0A
mov fsr,w
:zero_ram clr ind ;clear using indirect addressing
incsz fsr ;repeat until done
jmp :zero_ram
_bank bank0 ;clear bank 0 registers
clr $10
clr $11
clr $12
clr $13
clr $14
clr $15
clr $16
clr $17
clr $18
clr $19
clr $1a
clr $1b
clr $1c
clr $1d
clr $1e
clr $1f
;*********************************************************************************
; Initialize program/VP registers
;*********************************************************************************
;*********************************************************************************
; Setup and enable RTCC interrupt, WREG register, RTCC/WDT prescaler
;*********************************************************************************
RTCC_ON = %10000000 ;Enables RTCC at address $01 (RTW hi)
;*WREG at address $01 (RTW lo) by default
RTCC_ID = %01000000 ;Disables RTCC edge interrupt (RTE_IE hi)
;*RTCC edge interrupt (RTE_IE lo) enabled by default
RTCC_INC_EXT = %00100000 ;Sets RTCC increment on RTCC pin transition (RTS hi)
;*RTCC increment on internal instruction (RTS lo) is default
RTCC_FE = %00010000 ;Sets RTCC to increment on falling edge (RTE_ES hi)
;*RTCC to increment on rising edge (RTE_ES lo) is default
RTCC_PS_ON = %00000000 ;Assigns prescaler to RTCC (PSA lo)
RTCC_PS_OFF = %00001000 ;Assigns prescaler to RTCC (PSA lo)
PS_000 = %00000000 ;RTCC = 1:2, WDT = 1:1
PS_001 = %00000001 ;RTCC = 1:4, WDT = 1:2
PS_010 = %00000010 ;RTCC = 1:8, WDT = 1:4
PS_011 = %00000011 ;RTCC = 1:16, WDT = 1:8
PS_100 = %00000100 ;RTCC = 1:32, WDT = 1:16
PS_101 = %00000101 ;RTCC = 1:64, WDT = 1:32
PS_110 = %00000110 ;RTCC = 1:128, WDT = 1:64
PS_111 = %00000111 ;RTCC = 1:256, WDT = 1:128
mov w,#RTCC_PS_OFF ;setup option register
mov !option,w
jmp @main
org $200
;*****************************************************************************************
; Jump table for page 1
; Enables CALLs to functions in the second half of the page
;*****************************************************************************************
set_PWM1 jmp set_PWM1_
set_PWM2 jmp set_PWM2_
set_CAP1 jmp set_CAP1_
set_CAP2 jmp set_CAP2_
set_EXT1 jmp set_EXT1_
set_EXT2 jmp set_EXT2_
getFreq jmp getFreq_
;*****************************************************************************************
; Subroutines
;*****************************************************************************************
;*********************************************************************************
; Function: delay_10n_ms
; This subroutine delays 'w'*10 milliseconds (with RTCC of 217 cycles).
;
; Inputs:
; w - # of milliseconds to delay for.
; Outputs:
; none
; Registers affected:
; temp, timer_high, timer_low, timer_flag
;*********************************************************************************
delay_10n_ms mov function_temp,w
_bank timers
:loop clrb timer_flag ; This loop delays for 10ms
mov timer_high,#$f6
mov timer_low,#$d7
jnb timer_flag,$
dec function_temp ; do it w-1 times.
jnz :loop
clrb timer_flag
retp
;*********************************************************************************
; Function: set_PWM1
; Sets up Multi-function Timer 1 in PWM mode. The registers t1_hdc_high and
; t1_hdc_low set up the 16-bit high duty cycle value, and t1_ldc_high and t1_ldc_low
; setup the 16-bit low duty cycle value
;
; Inputs: t1_hdc_high, t1_hdc_low, t1_ldc_high, t1_ldc_low
;
; Outputs:
;
; Registers affected:
;
; Functions Called:
; none
;*********************************************************************************
set_PWM1_ _mode CLR_TMR ;clear Timer T1
mov w,#$00
mov !rb,w
;*************************************************************************
; Setup T1 control registers
; -PWM mode, prescaler=1:1
;*************************************************************************
_mode TCNTA_W ;write to T1CNTA
mov w,#$00
mov !rb,w
_mode TCNTB_W ;write to T1CNTB
mov w,#$01
mov !rb,w
;*************************************************************************
; Setup high duty-cycle via R1(16-bit)
;*************************************************************************
_mode TR1CMH_W ;write to T1R1CMH
mov w,t1_hdc_high
mov !rb,w
_mode TR1CML_W ;write to T1R1CML
mov w,t1_hdc_low
mov !rb,w
;*************************************************************************
; Setup low duty-cycle via R2(16-bit)
;*************************************************************************
_mode TR2CMH_W ;write to T1R2CMH
mov w,t1_ldc_high
mov !rb,w
_mode TR2CML_W ;write to T1R2CML
mov w,t1_ldc_low
mov !rb,w
retp
;*********************************************************************************
; Function: set_PWM2
; Sets up Multi-function Timer 2 in PWM mode.
;
; Inputs: t2_hdc_high, t2_hdc_low, t2_ldc_high, t2_ldc_low
;
; Outputs:
;
; Registers affected:
;
; Functions Called:
; none
;*********************************************************************************
set_PWM2_ _mode CLR_TMR ;clear Timer T2
mov w,#$00
mov !rc,w
;*************************************************************************
; Setup T2 control registers
; -PWM mode, prescaler=1:1
;*************************************************************************
_mode TCNTA_W ;write to T2CNTA
mov w,#$00
mov !rc,w
_mode TCNTB_W ;write to T2CNTB
mov w,#$01
mov !rc,w
;*************************************************************************
; Setup high duty-cycle via R1(16-bit)
;*************************************************************************
_mode TR1CMH_W ;write to T2R1CMH
mov w,t2_hdc_high
mov !rc,w
_mode TR1CML_W ;write to T2R1CML
mov w,t2_hdc_low
mov !rc,w
;*************************************************************************
; Setup low duty-cycle via R2(16-bit)
;*************************************************************************
_mode TR2CMH_W ;write to T2R2CMH
mov w,t2_ldc_high
mov !rc,w
_mode TR2CML_W ;write to T2R2CML
mov w,t2_ldc_low
mov !rc,w
retp
;*********************************************************************************
; Function: set_CP1
; Sets up Multi-function Timer 1 in Capture mode. A valid transition on the
; capture 1 pin captures the counter value into the dedicated capture registers
; (16-bit), T1CPL and T1CPH. A valid transition on the capture 2 pin captures
; the counter value into the R2 registers (16-bit), T1R2CML and T1R2CMH.
;
; Inputs: none
;
; Outputs: T1CPL, T1CPH, T1R2CML and T1R2CMH
;
; Registers affected:
;
;*********************************************************************************
set_CAP1_ _mode CLR_TMR ;clear Timer T1
mov w,#$00
mov !rb,w
;*************************************************************************
; Setup T1 control registers
; -Capture mode, prescaler=1:1
;*************************************************************************
_mode TCNTB_W ;write to T1CNTB
mov w,#%01000010 ;setup capture edge (T1CNTB.6),
mov !rb,w ;setup capture clock prescaler T1PS2:0 (T1CNTB.4:2) and
;enable Capture/Compare mode (T1CNTA.1:0 = 10b)
_mode TCNTA_W ;write to T1CNTA
mov w,#%00000000 ;setup capture interrupt (T1CNTA.5) and
mov !rb,w ;disable compare interrupt (T1CNTA.2)
;*************************************************************************
; Wait for Capture flag 1, T1CPF1 (T1CNTA.6)
;*************************************************************************
:again snb T1cap1_done
jmp :cap2
_mode TCNTA_R ;read from T1CNTA
mov !rb,w
mov function_temp,w
sb function_temp.6 ;check bit 6 (T1CPF1)
jmp :cap2
setb T1cap1_done ;T1 Capture 1 done, get 16-bit result
_mode TCPL_R ;read from T1CPL
mov !rb,w ;get T1CPL and,
_bank timers
mov T1CAP1L,w ;write it to T1CAP1L
_mode TCPH_R ;read from T1CPH
mov !rb,w ;get T1CPH and,
mov T1CAP1H,w ;write it to T1CAP1H
;*************************************************************************
; Wait for Capture flag 2, T1CPF2 (T1CNTA.7)
;*************************************************************************
:cap2 snb T1cap2_done
jmp :again
_mode TCNTA_R ;read from T1CNTA
mov !rb,w
mov function_temp,w
sb function_temp.7 ;check bit 7 (T1CPF2)
jmp :again
setb T1cap2_done ;T1 Capture 2 done, get 16-bit result
_mode TR2CML_R ;read from T1R2CML
mov !rb,w ;get T1R2CML and,
_bank timers
mov T1CAP2L,w ;write it to T1CAP2L
_mode TR2CMH_R ;read from T1R2CMH
mov !rb,w ;get T1R2CMH and,
mov T1CAP2H,w ;write it to T1CAP2H
retp
;*********************************************************************************
; Function: set_CP2
; Sets up Multi-function Timer 2 in Capture mode. A valid transition on the
; capture 1 pin captures the counter value into the dedicated capture registers
; (16-bit), T2CPL and T2CPH. A valid transition on the capture 2 pin captures
; the counter value into the R2 registers (16-bit), T2R2CML and T2R2CMH.
;
; Inputs: none
;
; Outputs: T1CPL, T1CPH, T1R2CML and T1R2CMH
;
; Registers affected:
;
;*********************************************************************************
set_CAP2_ _mode CLR_TMR ;clear Timer T2
mov w,#$00
mov !rc,w
;*************************************************************************
; Setup T2 control registers
; -Capture mode, prescaler=1:1
;*************************************************************************
_mode TCNTB_W ;write to T2CNTB
mov w,#%01000010 ;setup capture edge (T2CNTB.6),
mov !rc,w ;setup capture clock prescaler T2PS2:0 (T2CNTB.4:2) and
;enable Capture/Compare mode (T2CNTA.1:0 = 10b)
_mode TCNTA_W ;write to T2CNTA
mov w,#%00000000 ;setup capture interrupt (T2CNTA.5) and
mov !rc,w ;disable compare interrupt (T2CNTA.2)
;*************************************************************************
; Wait for Capture flag 1, T2CPF1 (T2CNTA.6)
;*************************************************************************
:again snb T2cap1_done
jmp :cap2
_mode TCNTA_R ;read from T2CNTA
mov !rc,w
mov function_temp,w
sb function_temp.6 ;check bit 6 (T2CPF1)
jmp :cap2
setb T2cap1_done ;T2 Capture 1 done, get 16-bit result
_mode TCPL_R ;read from T2CPL
mov !rc,w ;get T2CPL and,
_bank timers
mov T2CAP1L,w ;write it to T2CAP1L
_mode TCPH_R ;read from T2CPH
mov !rc,w ;get T2CPH and,
mov T2CAP1H,w ;write it to T2CAP1H
;*************************************************************************
; Wait for Capture flag 2, T2CPF2 (T2CNTA.7)
;*************************************************************************
:cap2 snb T2cap2_done
jmp :again
_mode TCNTA_R ;read from T2CNTA
mov !rc,w
mov function_temp,w
sb function_temp.7 ;check bit 7 (T2CPF2)
jmp :again
setb T2cap2_done ;T2 Capture 2 done, get 16-bit result
_mode TR2CML_R ;read from T2R2CML
mov !rc,w ;get T2R2CML and,
_bank timers
mov T2CAP2L,w ;write it to T2CAP2L
_mode TR2CMH_R ;read from T2R2CMH
mov !rc,w ;get T2R2CMH and,
mov T2CAP2H,w ;write it to T2CAP2H
retp
;*********************************************************************************
; Function: set_EXT1
; Sets up Multi-function Timer 1 in External Event mode. The registers t1_hdc_high and
; t1_hdc_low set up the 16-bit high duty cycle value, and t1_ldc_high and t1_ldc_low
; setup the 16-bit low duty cycle value
;
; Inputs: t1_hdc_high, t1_hdc_low, t1_ldc_high, t1_ldc_low
;
; Outputs:
;
; Registers affected:
;
; Functions Called:
; none
;*********************************************************************************
set_EXT1_ _mode CLR_TMR ;clear Timer T1
mov w,#$00
mov !rb,w
;*************************************************************************
; Setup T1 control registers
; -External Event mode, prescaler=1:1
;*************************************************************************
_mode TCNTA_W ;write to T1CNTA
mov w,#$00
mov !rb,w
_mode TCNTB_W ;write to T1CNTB
mov w,#$11
mov !rb,w
;*************************************************************************
; Setup high duty-cycle via R1(16-bit)
;*************************************************************************
_mode TR1CMH_W ;write to T1R1CMH
mov w,t1_hdc_high
mov !rb,w
_mode TR1CML_W ;write to T1R1CML
mov w,t1_hdc_low
mov !rb,w
;*************************************************************************
; Setup low duty-cycle via R2(16-bit)
;*************************************************************************
_mode TR2CMH_W ;write to T1R2CMH
mov w,t1_ldc_high
mov !rb,w
_mode TR2CML_W ;write to T1R2CML
mov w,t1_ldc_low
mov !rb,w
retp
;*********************************************************************************
; Function: set_EXT2
; Sets up Multi-function Timer 2 in External Event mode. The registers t2_hdc_high and
; t2_hdc_low set up the 16-bit high duty cycle value, and t2_ldc_high and t2_ldc_low
; setup the 16-bit low duty cycle value
;
; Inputs: t2_hdc_high, t2_hdc_low, t2_ldc_high, t2_ldc_low
;
; Outputs:
;
; Registers affected:
;
; Functions Called:
; none
;*********************************************************************************
set_EXT2_ _mode CLR_TMR ;clear Timer T2
mov w,#$00
mov !rc,w
;*************************************************************************
; Setup T1 control registers
; -External Event mode, prescaler=1:1
;*************************************************************************
_mode TCNTA_W ;write to T2CNTA
mov w,#$00
mov !rc,w
_mode TCNTB_W ;write to T2CNTB
mov w,#$03
mov !rc,w
;*************************************************************************
; Setup high duty-cycle via R1(16-bit)
;*************************************************************************
_mode TR1CMH_W ;write to T2R1CMH
mov w,t2_hdc_high
mov !rc,w
_mode TR1CML_W ;write to T2R1CML
mov w,t2_hdc_low
mov !rc,w
;*************************************************************************
; Setup low duty-cycle via R2(16-bit)
;*************************************************************************
_mode TR2CMH_W ;write to T2R2CMH
mov w,t2_ldc_high
mov !rc,w
_mode TR2CML_W ;write to T2R2CML
mov w,t2_ldc_low
mov !rc,w
retp
;*********************************************************************************
; Function: getFreq
;
; Inputs:
;
; Outputs:
;
; Registers affected:
;
; Functions Called:
; none
;*********************************************************************************
getFreq_ _mode CLR_TMR ;clear Timer T2
mov w,#$00
mov !rc,w
;*************************************************************************
; Setup T2 control registers
; -Capture mode, prescaler=1:1
;*************************************************************************
_mode TCNTB_W ;write to T2CNTB
mov w,#%01000010 ;setup capture edge (T2CNTB.6),
mov !rc,w ;setup capture clock prescaler T2PS2:0 (T2CNTB.4:2) and
;enable Capture/Compare mode (T2CNTA.1:0 = 10b)
_mode TCNTA_W ;write to T2CNTA
mov w,#%00000000 ;setup capture interrupt (T2CNTA.5) and
mov !rc,w ;disable compare interrupt (T2CNTA.2)
;*************************************************************************
; Wait for Capture flag 1, T2CPF1 (T2CNTA.6)
;*************************************************************************
:again _mode TCNTA_R ;read from T2CNTA
mov !rc,w
mov function_temp,w
sb function_temp.6 ;check bit 6 (T2CPF1)
jmp :again
setb T2cap1_done ;T2 Capture 1 done, get 16-bit result
_mode TCPL_R ;read from T2CPL
mov !rc,w ;get T2CPL and,
_bank timers
mov T2CAP1L,w ;write it to T2CAP1L
_mode TCPH_R ;read from T2CPH
mov !rc,w ;get T2CPH and,
mov T2CAP1H,w ;write it to T2CAP1H
retp
org $A00
;*****************************************************************************************
; MAIN PROGRAM CODE
;*****************************************************************************************
;*********************************************************************************
; Main
;*********************************************************************************
main
_bank timers
mov t1_hdc_high,#$00 ;load T1R1CMH value
mov t1_hdc_low,#$ff ;load T1R1CML value
mov t1_ldc_high,#$00 ;load T1R2CMH value
mov t1_ldc_low,#$ff ;load T1R2CML value
call @set_PWM1
; _bank timers
; mov t2_hdc_high,#$00 ;load T1R1CMH value
; mov t2_hdc_low,#$01 ;load T1R1CML value
; mov t2_ldc_high,#$00 ;load T1R2CMH value
; mov t2_ldc_low,#$01 ;load T1R2CML value
; call @set_EXT2
;*********************************************************************************
; Main Program Loop
;*********************************************************************************
main_loop
; jmp Variable_PWM
; call @set_CAP2
call @getFreq
jmp main_loop
;*********************************************************************************
; Function: Variable_PWM
; This function demonstrates how to setup and enable an onboard 16-bit timer in
; PWM mode and modulate the PWM output.
;*********************************************************************************
Variable_PWM
;*********************************************************************************
; Setup and enable onboard 16-bit timers in PWM mode.
;*********************************************************************************
:loop1 _bank timers
mov t1_hdc_high,#$ff ;load T1R1CMH value
mov t1_hdc_low,#$ff ;load T1R1CML value
mov t1_ldc_high,#$ff ;load T1R2CMH value
mov t1_ldc_low,#$ff ;load T1R2CML value
call @set_PWM1
mov w,#10
call @delay_10n_ms
;*********************************************************************************
; Only update PWM on overflow of R2
;*********************************************************************************
_mode TCNTA_W ;write to T1CNTA (to clear the flags)
mov w,#$00
mov !rb,w
_mode TCNTA_R ;read T1CNTA (to check T1CMF2)
:loop2 mov w,#$00
mov !rb,w
sb wreg.4 ;wait until T1CMF2 gets set
jmp :loop2
;*********************************************************************************
; Reload onboard 16-bit timers with new values.
;*********************************************************************************
_bank timers
mov t1_hdc_high,#$7f ;load T1R1CMH value
mov t1_hdc_low,#$ff ;load T1R1CML value
mov t1_ldc_high,#$7f ;load T1R2CMH value
mov t1_ldc_low,#$ff ;load T1R2CML value
call @set_PWM1
mov w,#10
call @delay_10n_ms
;*********************************************************************************
; Only update PWM on overflow of R2
;*********************************************************************************
_mode TCNTA_W ;write to T1CNTA (to clear the flags)
mov w,#$00
mov !rb,w
_mode TCNTA_R ;read T1CNTA (to check T1CMF2)
:loop3 mov w,#$00
mov !rb,w
sb wreg.4 ;wait until T1CMF2 gets set
jmp :loop3
jmp :loop1
;*****************************************************************************************
; END OFMAIN PROGRAM CODE
;*****************************************************************************************
;*****************************************************************************************
END ;End of program code
;*****************************************************************************************
| file: /Techref/scenix/sx48-52timers.htm, 41KB, , updated: 2002/11/1 18:08, local time: 2024/12/27 10:22,
owner: JMN-EFP-786,
3.142.198.108:LOG IN
|
| ©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions? <A HREF="http://ecomorder.com/techref/scenix/sx48-52timers.htm"> Timer examples</A> |
| Did you find what you needed? |
Welcome to ecomorder.com! |
Welcome to ecomorder.com! |
.