(as listed by himself)
Automatic Masker for Hughes Aircraft in Newport Beach
This machine is used in the manufacture of semiconductors (transistors and diodes). It transports light sensitized fragile one inch diameter silicon slices of .016 thickness under a photographic mask, applies a pressure to ensure good contact between mask and slice, and optically exposes the slices to ultraviolet light. It is ten times faster then the same job done manually. It is controlled electronically using closed-loop feedbacks with vacuum (pneumatic) actuation of my own design.
Manual Alignment Fixture for Hughes Aircraft.
This device performs a similar job as above except manually. It costs $150 to manufacture and can do the same work as a $2000 machine.
Photoresist Spinner for Hughes Aircraft.
This machine holds silicon slices for coating with ultraviolet sensitive photoresist. It uses a vacuum that is fed into a rotating shaft. No seals are used and rotational speed is in excess of 10,000 rpm.
Motor Control using Light
This device controls a 1/10 hp electric motor driving a milling machine table leadscrew. A lever which is manually positioned to control table speed, is used to change the intensity of light, via a "flag" with a tapered slot, on a light dependent resistor (LDR) which modifies the triggering of the controlling silicon controlled rectifier (SCR). Very little force on the moveble lever is required as contrasted with other system of control.
Tapping Device
This attachment is used on a lathe with a reversible motor for tapping metal bar stock. It reverses a 1/2 hp electric motor driving the lathe headstock when the machine screw tap becomes clogged with metal chips, which prevent breaking the tap and facilitater quick and easy removal of the chips.
Diode Testing Transport Fixture Mechanism
This machine accepts electrical diodes and positions them such that they can be electrically tested, then sorts them on a go no-go basis. It utilizes dash-pot damping in conjunction with electrical solenoids.
Pipe Conveyor for Non-Destruction testing for Microwave Instruments, in Corona Dal Mar.
This machine, about two feet square, contains "V" rollers to support and transport a pipe up to 2" in diameter through a test coil housing to detect, mark, and sort flaws withing the pipe. The machine contains photocells and lamps, electronic pipe flaw detection amplifier and related control switches. The first was so successful that two additional machines were ordered and have been built.
Universal Transfer Machine for Mesamatics in Costa Mesa
This was an engineering application of a principle conceived by the customer. The machine is a prototype to sell the idea of flexible local automation on the Detroit automobile manufacturing assembly lines. It is programmed by recording on multiple discs coated with wax with a hot stylus so that pantographic arms would follow, with magnification through a servo-mechanism, the varying grooves. It used cloned-loop reset type off and on motor control.
Actuator for Boeing Aircraft
This precision mechanical actuator was part of a system to measure metal thickness using the reflection of microwaves to maintain a consistent distance between the sensing head and the work; this location or position was then sent digitally to an add or subtract counter, which was translated into thickness expressed in "mils".
Flux Pickoff Spinning Machine for Microwave Instruments
This machine detects flaws in ferrous pipe by a non-destructive method; a spinning ferrite probe diverts the magnetic flux pattern to a surrounding coil and as the pattern changes due to anomalies in the pipe this information is transferred to a computer (which I constructed) for readout.
James also designed an build an automatic manufacturing machine for the product described in this patent: US2887218A. The machine used pneumatic cylinders controlled from a rotating bank of cams which actuated pneumatic switches. Time variable processes paused the rotation until sensors indicated the step was complete. Sensors could also detect jams and pause operation while buzzing to signal an operator. Feeding the card stock covers, foil, etc... were also automated with electrical actuators and sensors. For example, a photocell detected the level of card stock and ran motor to raise the chain drive lift feed so that stock was always available at the top level.
+
file: /Techref/other/newtons/ps01/ps01_077accomplishments.htm, 5KB, , updated: 2021/8/5 10:01, local time: 2024/8/14 20:25,
owner: JMN-EFP-786,
3.147.28.23:LOG IN
|
©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions? <A HREF="http://ecomorder.com/techref/other/newtons/ps01/ps01_077accomplishments.htm"> Accomplishments of James C. Newton</A> |
Did you find what you needed? |
Welcome to ecomorder.com! |
Welcome to ecomorder.com! |
.