PIC 4 bit 16x2 Hitachi LCD driver

by Stefan Johansson

Simple routines for controlling a HD44780 display. Useful if you are adding a display to an old project. The data bus and control lines can use any pin. It works just fine on pic 16f677 and 16f877.

Code:

Stefan Johansson shares this code:


;**********************************************************************
; Simple routines for controlling a HD44780 display                   *
; Useful if you are adding a display to an old project.               *
; The data bus and control lines can use any pin.                     *
; If the pin is open collector you need a pull up resistor            *
;                                                                     *
;**********************************************************************
;                                                                     *
;    Filename:	    lcd.asm                                           *
;    Date:          20080204                                          *
;    File Version:  1.1                                               *
;                                                                     *
;    Author:        Stefan Johansson                                  *
;                   tessier at telia dot com                          *
;                                                                     *
;**********************************************************************
;                                                                     *
;    Usage: #include 	<lcd.asm>                                     *
;			call	LCDINIT		; Initialize LCD      *
;                                                                     *
;			movlw	0x05                                  *
;			call	LCDADD		; Goto lcd adress 0x05*
;                                                                     *
;			movlw	'A'                                   *
;			call	LCDSEND		; Write character A   *
;**********************************************************************
;                                                                     *
;	Variables:	D0					      *
;			D1					      *
;			D2				              *
;			LCDTmp					      *
;                                                                     *
;**********************************************************************
;                                                                     *
;    Notes: This was written and compiled for PIC 16f677.	      *
;           Modification might be needed for other models.	      *
;           Any comments, questions or improvements... mail me        *
;                                                                     *
;**********************************************************************


	; LCD control lines
	; Modify to match your project
	#define LCD_D4	PORTB, 3
	#define LCD_D5	PORTB, 2	; 4 data lines
	#define LCD_D6	PORTB, 1
	#define LCD_D7	PORTB, 0
	#define	LCD_RS	PORTB, 5	; 0 = Command, 1 = Data
	#define LCD_E	PORTB, 4	; 1 to send data


;*************************************************************
; Initialize LCD functions
;*************************************************************
LCDINIT
; Set correct TRIS values for LCD ports
	bsf 	STATUS, RP0 		;Bank 1
	bcf	LCD_RS
	bcf	LCD_E
	bcf	LCD_D4
	bcf	LCD_D5
	bcf	LCD_D6
	bcf	LCD_D7
	bcf	STATUS, RP0		;Bank 0

	movlw	0x40			; Initial delay, probably not needed...
	call	delay
	
	; Forced LCD initialization
	bcf	LCD_RS			; Set command mode
	bcf	LCD_E
	bsf	LCD_D4
	bsf	LCD_D5
	bcf	LCD_D6
	bcf	LCD_D7
	call	PULSE
	
	movlw	0x04
	call	delay
	
	call	PULSE	
	call	short_dly
	call	short_dly
	call	PULSE

	; Send the command to select 4-bit mode first
	bcf	LCD_D4
	call	PULSE

	; Function set
	; Format: xxxDNFxx		  D: 1= 8-bit, 0= 4-bit (use 4-bit!)
	movlw	b'00101000'		; N: 1= 2 lines, 0= 1 line
	call	LCDSEND			; F: 1= 5x10 font, 0= 5x8 font
	
	; Display control
	; Format: xxxxxDCB		  D: Display on(1)/0ff(0) 
	movlw	b'00001100'		; C: Cursor on(1)/0ff(0) 
	call	LCDSEND			; B: Blink on(1)/0ff(0) 
	
	; Entry mode set
	; Format: xxxxxxIS		  I: 1= Increment counter, 0= Decrement counter
	movlw	b'00000110'		; S: 1= "Accompanies display shift"
	call	LCDSEND

	; Cursor or display shift
	; Format: xxxxSRxx		  S: 1= Display shift, 0= Cursor move
	movlw	b'00010000'		; R: 1= Shift right, 0= Shift left
	call	LCDSEND

	movlw	b'00000001'		; Clear screen
	call	LCDSEND	

	bsf	LCD_RS		        ; Set data mode
	RETURN


;*************************************************************
; Moves "cursor"
;*************************************************************
LCDADD
	bcf	LCD_RS			; Command mode
	iorlw	0x80			; Goto DDRAM adress
	call	LCDSEND
	bsf	LCD_RS			; Data mode
	call	delay_1ms		; Takes a couple of ms
	RETURN


;*************************************************************
; Sends contens of W to display
;*************************************************************
LCDSEND	; Sends character in W to lcd. Does not alter RS line!
	movwf	LCDTmp
	bcf	LCD_D4
	bcf	LCD_D5
	bcf	LCD_D6
	bcf	LCD_D7

	btfsc	LCDTmp, 7
		bsf	LCD_D7
	btfsc	LCDTmp, 6
		bsf	LCD_D6
	btfsc	LCDTmp, 5
		bsf	LCD_D5
	btfsc	LCDTmp, 4
		bsf	LCD_D4
	call	PULSE


	bcf	LCD_D4
	bcf	LCD_D5
	bcf	LCD_D6
	bcf	LCD_D7

	btfsc	LCDTmp, 3
		bsf	LCD_D7
	btfsc	LCDTmp, 2
		bsf	LCD_D6
	btfsc	LCDTmp, 1
		bsf	LCD_D5
	btfsc	LCDTmp, 0
		bsf	LCD_D4
	call	PULSE

	return


;*************************************************************
; Pulse enable line
;*************************************************************
PULSE ; Pulse Enable.
	bsf	LCD_E
	nop				; Increase the delay here if you get
	nop				; problems with high clock speed
	nop				; Probably not needed since 
        nop				; 1 instruction @10MHz = 400ns
	bcf	LCD_E
	call	delay_1ms
	call	delay_1ms
	return


;*************************************************************
; Clears display
;*************************************************************
LCDCLR ; clears the entire display
	bcf	LCD_RS			; Set command mode
	movlw	b'00000001'		; Clear screen
	call	LCDSEND	
	bsf	LCD_RS			; Set data mode

	return


;*************************************************************
; Calls the delay_1ms W times
;*************************************************************
delay
	movwf	d0
dly_loop
	call	delay_1ms
	decfsz	d0, F
	goto	dly_loop
	return


;*************************************************************	
; 1ms delay.
; Modify this to match your processor speed.
; http://www.piclist.com/techref/piclist/codegen/delay.htm
;*************************************************************
delay_1ms
	movlw	0xF3		;2498 cycles
	movwf	d1
	movlw	0x02
	movwf	d2
Delay_0
	decfsz	d1, f
	goto	$+2
	decfsz	d2, f
	goto	Delay_0
	goto	$+1		;2 cycles
	return			;4 cycles (including call)


;*************************************************************	
; 40us delay.
; Modify this to match your processor speed.
; http://www.piclist.com/techref/piclist/codegen/delay.htm
;*************************************************************
short_dly
	movlw	0x1F		;94 cycles
	movwf	d1
short_dly_0
	decfsz	d1, f
	goto	short_dly_0
	goto	$+1		;2 cycles
	return			;4 cycles (including call)

Comments:

This is right:
; Format: xxxxSRxx S: 1= Display shift, 0= Cursor move
movlw b'00001000' ; R: 1= Shift right, 0= Shift left+

Works fine, just have to edit the beginning of the code to

#include <yourpic.pic>
call	LCDINIT		; Initialize LCD
movlw	0x05                                  
call	LCDADD		
movlw	'A'
call	LCDSEND		; Write character A   *
                                                              
;	Variables:
d0 equ 0x20					      
d1 equ 0x21
d2 equ 0x22				              
LCDTmp	equ 0x23

AND IT WORKS, thanks to the author.+

spamcleman at drallim.com " I had include the PIC16F87X.inc file and define d0,d1,d2 and LCDTemp before it compiled."
this code DOES NOT WORK.
Stefan Johansson replies: But it works for me... Anyone else?
+
+

file: /Techref/io/LCD/lcd.asm.htm, 9KB, , updated: 2012/2/6 15:13, local time: 2024/12/2 03:59, owner: SJ-telia-G32,

^{3.148.108.201:LOG IN}

©2024 These pages are served without commercial sponsorship. (No popup ads, etc...).Bandwidth abuse increases hosting cost forcing sponsorship or shutdown. This server aggressively defends against automated copying for any reason including offline viewing, duplication, etc... Please respect this requirement and DO NOT RIP THIS SITE. Questions?

Please DO link to this page! Digg it! / MAKE!

<A HREF="http://ecomorder.com/Techref/io/LCD/lcd.asm.htm"> Simple routines for controlling a HD44780 display. Useful if you are adding a display to an old project. The data bus and control lines can use any pin. It works just fine on pic 16f677 and 16f877.</A>

Did you find what you needed?

PIC 4 bit 16x2 Hitachi LCD driver

by Stefan Johansson

Welcome to ecomorder.com!

Welcome to ecomorder.com!